|
DESCRIPTION: BOYSEN® Flat Wall Enamel is a flat, alkyd- type paint that is both durable and fast- drying. It is formulated to give a tough and beautiful finish on wood and metal. Because of its superior hiding properties, it can also be used as a primer for enamel coatings. It levels evenly and shows no lap and brush marks when applied skillfully.
PRINCIPAL USES: It is ideal for interior and exterior wood and metal surfaces.
FINISH: Flat
DRY TIME:
Touch: 1 hour
Recoat: 2 hours
Full cure: 8 hours
THEORETICAL COVERAGE PER 4-LITERS: 25 - 30 sq. m.
*Depending on surface texture and porosity
TINTING: Will accept BOYSEN® Oil Tinting Colors at a maximum level of ¼ Liter per 4-Liter can. Take note that B-2319 Hansa Yellow and B- 2315 Bulletin Red are for interior painting only.
THINNING SOLVENT: Thin with not more than 1-Liter of BOYSEN® Paint Thinner B-0340 per 4-Liter can of BOYSEN® alkyd enamel products.
CLEAN-UP SOLVENT: BOYSEN® Paint Thinner B-0340
PACKAGING: 1-Liter, 4-Liters, and 16-Liters
APPLICATION: By brush or roller
AVAILABLE COLORS: Whites may be tinted to pastel or light shades using BOYSEN® Oil Tinting Colors. Also available in B-691 Flat Black.
|
|
DESCRIPTION: BOYSEN® Flat Wall Enamel is a flat, alkyd- type paint that is both durable and fast- drying. It is formulated to give a tough and beautiful finish on wood and metal. Because of its superior hiding properties, it can also be used as a primer for enamel coatings. It levels evenly and shows no lap and brush marks when applied skillfully.
PRINCIPAL USES: It is ideal for interior and exterior wood and metal surfaces.
FINISH: Flat
DRY TIME:
Touch: 1 hour
Recoat: 2 hours
Full cure: 8 hours
THEORETICAL COVERAGE PER 4-LITERS: 25 - 30 sq. m.
*Depending on surface texture and porosity
TINTING: Will accept BOYSEN® Oil Tinting Colors at a maximum level of ¼ Liter per 4-Liter can. Take note that B-2319 Hansa Yellow and B- 2315 Bulletin Red are for interior painting only.
THINNING SOLVENT: Thin with not more than 1-Liter of BOYSEN® Paint Thinner B-0340 per 4-Liter can of BOYSEN® alkyd enamel products.
CLEAN-UP SOLVENT: BOYSEN® Paint Thinner B-0340
PACKAGING: 1-Liter, 4-Liters, and 16-Liters
APPLICATION: By brush or roller
AVAILABLE COLORS: Whites may be tinted to pastel or light shades using BOYSEN® Oil Tinting Colors. Also available in B-691 Flat Black.
|
|
SURFACE PREPARATION:
Wooden Surfaces
Surface to be painted should be clean and dry, free from dust, dirt, and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth and then dust off before painting.
For repainting, scrape off all loose, scaling, flaking, and peeling paint as necessary. Make sure surface is clean, dry, and good weather persists prior to painting. Prime with BOYSEN® Flatwall Enamel B-800 before recoating.
Metal Surfaces
Wipe the surface with a rag soaked in paint thinner to remove grease, oil, wax and other foreign matter. For new galvanized surfaces, etch the surface by applying 10% BOYSEN® Metal Etching Solution B-71 (Dilute 1 part of B-71 to 9 parts water). Rinse with water and dry immediately.
Unpainted galvanized surfaces that have been exposed for 6 months or more need not be etched.
For recoating pre-painted galvanized surfaces in good condition, sand lightly then wipe the surface with a clean rag before applying paint. Remove all loose paint film to sound surface. Spot prime bare substrate.
For corroded galvanized surfaces, remove rust by wire brushing and use BOYSEN® Metal Etching Solution B-71. Let it stay for 10-15 minutes. Be sure to remove all remaining residue. Immediately prime after drying.
PAINTING SCHEDULE:
Wooden Surfaces
1st Coat: BOYSEN® Flatwall Enamel B-800
Putty: BOYSEN® Plasolux Glazing Putty B-311
2nd & 3rd Coat: BOYSEN® Flatwall Enamel B-800
Metal Surfaces
1st Coat: BOYSEN® Red Oxide Metal Primer B-310
2nd & 3rd Coat: BOYSEN® Flatwall Enamel B-800
|
